This drain can be used with or without a threshold.
To use with:
• A wall in the back of the drain;
• A wall on the right side of the drain and a threshold on the left;
• A wall on the left side of the drain and a threshold on the right;
• A wall on each side of the drain.

Important :The finishing grid is designed for tiles of a certain thickness; between 5/16 and 3/8. If your tiles are thicker or less thick than the measures above-mentioned or if you are using mosaic tiles of a square inch and less, it is important to specify it when you place your order.

This drain can only be used with a polished concrete finishing. It cannot be used with ceramic tiles. The drain can be used with or without a threshold.
To use with:
• A wall in the back of  the drain;
• A wall on the right of the drain and a threshold on the left;
• A wall on the left of the drain and a threshold on the right;
• A wall on each side of the drain.

Important: Before ordering this model it is essential to know the exact thickness of the concrete slab that is going to be poured, in order to figure out the height of the finishing grid.

This drain can only be used with a threshold.
To use with:
• A wall on the right and a threshold on the left;
• A wall on the left and a threshold on the right;
• A wall on the right and a wall on the left;
• A wall in the back.
To install on a concrete slab when the structure and/or the plumbing drain cannot be modified, like in condos for instance. It is necessary to build the slopes of the shower on a layer of sand coat.

Important: The finishing grid is designed for tiles of a certain thickness; between 5/16 and 3/8. If your tiles are thicker or less thick than the measures above-mentioned or if you are using mosaic tiles of a square inch and less, it is important to specify it when you place your order.

The drain can only be used with a threshold.
To use with:
• A wall on the right and a threshold on the left;
• A wall on the left and a threshold on the right;
• A wall on the right and on the left.
To install on a concrete slab when the structure and/or the plumbing drain cannot be modified, like in condos for instance. It is necessary to build the slopes of the shower on a layer of sand coat. This drain is equipped with a stronger finishing grid.

Important: The finishing grid is designed for tiles of a certain thickness; between 5/16 and 3/8. If your tiles are thicker or less thick than the measures above-mentioned or if you are using mosaic tiles of a square inch and less, it is important to specify it when you place your order.

This drain can only be used with a threshold.
To use with:
• Two walls in the back.
This drain has to be installed in a corner.

Important: The finishing grid is designed for tiles of a certain thickness; between 5/16 and 3/8. If your tiles are thicker or less thick than the measures above-mentioned or if you are using mosaic tiles of a square inch and less, it is important to specify it when you place your order.

The drain can be used with or without a threshold.
To use with:
• A threshold and three walls;
• Two thresholds and two walls;
• Three thresholds and a wall.
This drain is equipped with a stronger finishing grid.

Important: The finishing grid is designed for tiles of a certain thickness; between 5/16 and 3/8. If your tiles are thicker or less thick than the measures above-mentioned or if you are using mosaic tiles of a square inch and less, it is important to specify it when you place your order.

The drain can be used with or without a threshold.
To use with:
• A wall on the right of the drain;
• A wall on the left of the drain;
• A glass panel in the back.
This drain is equipped with a decorative band which will be used for hiding the part of the floor that is ¾ of an inch higher than the front of the drain. It will also hide the thickness of the floor once it is finished. The band will be of the same finish as the finishing grid. The glass panel will then have to be placed 1/8 of an inch away from the interior edge of the shower. After you need to do the sealing.

Important: The finishing grid is designed for tiles of a certain thickness; between 5/16 and 3/8. If your tiles are thicker or less thick than the measures above-mentioned or if you are using mosaic tiles of a square inch and less, it is important to specify it when you place your order.

The drain can only be used without a threshold.
To use with:
• A wall on the right of the drain;
• A wall in the back of the drain.
The glass panel on the left side of the shower has to be installed on the bathroom floor, 1/8 of an inch away from the interior edge of the shower. The glass panel cannot be installed in the slope.

Important: The finishing grid is designed for tiles of a certain thickness; between 5/16 and 3/8. If your tiles are thicker or less thick than the measures above-mentioned or if you are using mosaic tiles of a square inch and less, it is important to specify it when you place your order.

This drain can only be used without a threshold.
To use with:
• A wall on the left of the drain;
• A wall in the back of the drain.
The glass panel on the right side of the shower has to be installed on the bathroom floor, 1/8 of an inch away from the interior edge of the shower. The glass panel cannot be installed in the slope.

Important:The finishing grid is designed for tiles of a certain thickness; between 5/16 and 3/8. If your tiles are thicker or less thick than the measures above-mentioned or if you are using mosaic tiles of a square inch and less, it is important to specify it when you place your order.

The drain can only be used with a threshold.
To use with:
• A wall or a threshold on the left side;
• A wall in the back.
With this model, it is necessary to build two slopes of drainage.

Important: The finishing grid is designed for tiles of a certain thickness; between 5/16 and 3/8. If your tiles are thicker or less thick than the measures above-mentioned or if you are using mosaic tiles of a square inch and less, it is important to specify it when you place your order.

This drain can only be used with a threshold.
To use with:
• A wall or a threshold on the right;
• A wall in the back.
With this model, it is necessary to build two slopes of drainage.

Important: The finishing grid is designed for tiles of a certain thickness; between 5/16 and 3/8. If your tiles are thicker or less thick than the measures above-mentioned or if you are using mosaic tiles of a square inch and less, it is important to specify it when you place your order.

This drain can only be used with a polished concrete finishing. It cannot be used with ceramic tiles. The drain can only be used without a threshold.
To use with:
• A wall on the left of the drain;
• A wall in the back of the drain.
The glass panel on the right side of the shower has to be installed on the bathroom floor, 1/8 of an inch away from the interior edge of the shower. The glass panel cannot be installed in the slope.

Important: Before ordering this model it is essential to know the exact thickness of the concrete slab that is going to be poured, in order to figure out the height of the finishing grid.

This drain can only be used with a polished concrete finishing. It cannot be used with ceramic tiles. The drain can only be used without a threshold.
To use with:
• A wall on the right of the drain;
• A wall in the back of the drain.
The glass panel on the left side of the shower has to be installed on the bathroom floor, 1/8 of an inch away from the interior edge of the shower. The glass panel cannot be installed in the slope.

Important: Before ordering this model it is essential to know the exact thickness of the concrete slab that is going to be poured, in order to figure out the height of the finishing grid.

This drain can only be used without a threshold.
To use with:
• A wall in the back of the drain.
The glass panels of the shower(on the left and on the right side) has to be installed on the bathroom floor, 1/8 of an inch away from the interior edge of the shower. The glass panels cannot be installed in the slope.

Important: The finishing grid is designed for tiles of a certain thickness; between 5/16 and 3/8. If your tiles are thicker or less thick than the measures above-mentioned or if you are using mosaic tiles of a square inch and less, it is important to specify it when you place your order.

This model can only be used with a threshold.
To use with:
• A wall in the back.
With this model, it is necessary to build three slopes of drainage.

Important: The finishing grid is designed for tiles of a certain thickness; between 5/16 and 3/8. If your tiles are thicker or less thick than the measures above-mentioned or if you are using mosaic tiles of a square inch and less, it is important to specify it when you place your order.

This drain can only be used with a polished concrete finishing. It cannot be used with ceramic tiles. The drain can only be used without a threshold.
To use with:
• A wall in the back of the drain.
The glass panels of the shower(on the left side and on the right side) has to be installed on the bathroom floor, 1/8 of an inch away from the interior edge of the shower. The glass panels cannot be installed in the slope.

Important: Before ordering this model it is essential to know the exact thickness of the concrete slab that is going to be poured, in order to figure out the height of the finishing grid.

This drain can be used with or without a threshold.
With this model, it is necessary to build four slopes of drainage.
This drain is equipped with a stronger finishing grid.

Important: The finishing grid is designed for tiles of a certain thickness; between 5/16 and 3/8. If your tiles are thicker or less thick than the measures above-mentioned or if you are using mosaic tiles of a square inch and less, it is important to specify it when you place your order.